Looking at tub to shower conversion in Houston 77014? That’s around 19 miles from us, well inside the area we work daily.
A shower that was built wrong looks identical to one built right for about the first eighteen months. Then a grout line darkens, a tile at the curb sounds hollow, the baseboard in the adjoining room swells, or a stain appears on a ceiling below. By then water has been moving through the assembly for a long time, and the repair means removing everything back to studs. The failures are not mysterious. They are a short list of specific construction shortcuts, each of which is invisible after tile day. This is that list, and how each one is prevented.
What we see in Houston
Houston is not one housing stock, so it is not one kind of remodel. In the Heights and Woodland Heights you are often working on 1910s–1930s wood-frame homes on pier-and-beam, where leveling, sill and joist repair, and original wiring long past its service life come before anything cosmetic — and where a home in a designated historic district brings design review with it. Montrose, Oak Forest and Garden Oaks add mid-century layers. Meyerland, Westbury, Braeswood and Sharpstown are largely 1950s–60s slab ranch: cast iron drains near the end of their life, galvanized supply, single-pane windows, popcorn ceilings that should be tested before they are disturbed. Memorial and Alief lean 1970s–80s, which brings aluminum branch wiring and polybutylene supply into the conversation. West of Beltway 8 you are usually in 2000s and 2010s construction, where the job is upgrade rather than repair. Houston has no zoning, but plumbing, electrical and structural work is permitted, and deed restrictions still govern a great deal.
What we actually do
No pre-slope: the waterproofing membrane must sit on a surface that already slopes to the drain, so water reaching the membrane can exit. A flat membrane with slope built only above it holds standing water in the assembly permanently.
Wrong drain assembly: a shower drain has to bond to the waterproofing at the flange. A tub drain or the wrong clamping ring means water bypasses the connection.
Unsealed corners and transitions: inside corners, curb-to-floor and wall-to-floor junctions are where membranes tear and liquid systems go thin. Preformed corners or reinforced detailing belong at every one.
Curb built wrong: a curb wrapped without continuous waterproofing over its top and both faces, or fastened through the membrane on the inside face, leaks straight into the framing.
Grout where sealant belongs: rigid grout at changes of plane cracks with normal building movement. Flexible sealant belongs at inside corners and at floor-to-wall.
Skipping the flood test: the only chance to catch all of the above cheaply.
Mixing systems: using components from incompatible waterproofing systems is a common way to void the assembly’s integrity.
And on the surface side, hollow-sounding tile from poor mortar coverage, and a niche sloped the wrong way so it holds water.
Choosing materials
Grout choice ages the most visibly. Cementitious grout is porous and takes on colour from minerals and product residue; high-performance and epoxy-modified grouts resist that better, cost more, and are less forgiving to install. Silicone at plane changes has a service life and is a consumable, expected to be cut out and replaced periodically rather than lasting the life of the shower. Glass coatings are also consumable; factory-applied treatments last longer than aftermarket ones but both wear. Porcelain body tile is effectively permanent. Natural stone in a Houston shower is a maintenance commitment, since it needs sealing and reacts to acidic cleaners people reach for against scale. Valve cartridges are wear items and worth choosing from a line that stays in production. Hardware finishes vary: living finishes patina, and chrome and quality PVD hold up better against hard water than cheap plated brass, which pits at the base of hinges first.
Why this is different on the Gulf Coast
Houston’s slab movement is what turns a small detailing shortcut into a leak. Expansive clay swells and shrinks with the seasons, and the house moves with it. A shower with rigid grout at every corner will crack at those corners — reliably, not occasionally. Once cracked, the grout is no longer a barrier, and the only thing standing between the water and your framing is the waterproofing behind it. If the waterproofing was detailed poorly, that is the moment it starts to matter. Flexible sealant at changes of plane, movement joints where they are required, and crack-isolation on floors are the standard defenses.
Humidity is the second factor. High ambient moisture slows curing of waterproofing membranes, thinsets and grout, and a schedule that pushes past the cure windows undermines the assembly. It also means a shower dries slowly after use, which keeps everything wet longer and gives any defect more opportunity.
Ventilation is the practical remedy, and the most commonly deficient item in Houston bathrooms — undersized fans, crushed flexible duct, and terminations dumping into the attic. And hard water etches glass over time, which is cosmetic but is the complaint we hear most after a shower is finished.
Where these jobs fail
Tiling over greenboard. It is a paper-faced gypsum product, not a wet-area substrate, and it is still found behind failed 1980s showers here weekly. Building a pan with no pre-slope under the membrane, so water sits in the mortar bed permanently. Skipping the flood test: plug the drain, fill the pan, mark the level, walk away and come back before any tile is set. Mixing waterproofing brands, particularly a foam board from one system with the corner bands and drain flange of another. Failing to bond the membrane properly to the drain flange, which is the single most common origin of a leak that shows up on a ceiling below. Running the exhaust duct into the attic instead of through the roof or wall, which just moves the moisture. Building a curb from untreated lumber and tiling it with no membrane wrap. Ordering glass off the framing dimensions rather than templating after tile, then discovering the walls are not plumb. In older houses, closing walls without replacing the galvanised behind them.
What to expect
The concealed work gets documented. Before tile, you should receive photographs of the pre-slope, the drain connection, the corner detailing, the completed membrane and the flood test with water standing in the pan. That record is the only proof of how the shower was built.
Substrate work comes before anything else: framing corrected to plane, blocking in for bench, grab bars, niche and glass hardware, and a floor that is sound.
The pan is built with continuous slope, the waterproofing is installed as a single manufacturer’s system rather than a mix of parts, and the flood test runs before a single tile is set.
Tile follows with proper mortar coverage — checked, not assumed — and sealant rather than grout at every change of plane.
At handover you get plain guidance on caring for grout, sealant and glass in a hard-water area, and on running the exhaust fan long enough to actually dry the room.
What moves the price
Correct waterproofing is not the expensive part of a shower. Membranes, preformed corners and a proper bonding drain are a small fraction of a tile job, and the labor to detail them properly is hours, not days. The flood test costs a day of waiting.
What is expensive is the repair. A failed shower means demolition of tile, substrate, pan and often framing, plus the damage in adjacent rooms and any floor below. That is the entire shower done twice, with drying time in between.
Costs also rise where the existing construction is compromised — rotted framing at the curb or below the pan, damaged subfloor, or a slab that must be opened to correct a drain.
Design choices affect maintenance risk: large-format tile means fewer grout lines to fail, mosaic floors mean far more, and a curbless design puts more demand on the transition detailing.
The reasonable conclusion is to spend on the parts nobody will ever see and to be less precious about the parts they will.
Common questions
My grout is cracking in the corners. Is my shower leaking?
Not necessarily, but it needs attention. Cracked grout at inside corners is extremely common in Houston because rigid grout cannot accommodate the movement a slab home experiences. The correct material there is flexible sealant. Removing the cracked grout and replacing it with sealant is a reasonable repair. If tiles nearby sound hollow, or you see moisture in an adjacent room, that points to something behind the tile and warrants investigation.
How do I know my shower was waterproofed correctly?
Once it is tiled, you largely cannot — which is why photographs during construction matter so much. Ask for images of the sloped base, the drain connection, the corner treatments, the finished membrane and the flood test. If you are buying a house with a recently renovated bathroom and no such record exists, you are trusting the work sight unseen. It is a fair question to ask a seller or a contractor.
Can a leaking shower be repaired without tearing it out?
Occasionally, if the leak is genuinely at the surface — a failed sealant joint, a cracked grout line, or a loose fixture escutcheon. Those are worth trying first. But if water is getting past the tile into the assembly, surface repairs only slow it. There is no reliable way to repair a failed pan or a torn membrane from the finished side. The honest answer in that case is rebuild.
How long should a properly built tiled shower last?
With correct construction and reasonable maintenance, a very long time — the failures we see are overwhelmingly construction defects rather than wear. What does need periodic attention is the sealant at changes of plane, which should be inspected and renewed before it opens, and the grout, which benefits from being kept clean and intact. Ventilation matters too; a shower that never fully dries ages faster than one that does.
Do you cover Houston 77014?
Yes. Houston 77014 is about 19 miles from our shop at 1530 W Sam Houston Pkwy N, Houston, TX 77043, inside the area we work in daily. Call (281) 235-6971 to arrange a site visit.
MS Home Remodeling — tub to shower conversion in Houston, TX 77014. Call (281) 235-6971 for a site visit.