Kitchen demo and rebuild for homes in Katy, TX 77450 — about 5.7 miles from our shop at 1530 W Sam Houston Pkwy N, Houston, TX 77043.
Most kitchen projects that go badly do not go badly because someone hung a cabinet crooked. They go badly because of sequencing and decisions: selections made too late, appliances ordered after cabinets were built, a circuit that was needed after drywall closed, a wall removed before anyone confirmed what it carried. These mistakes are expensive precisely because they require undoing finished work. The good news is that nearly all of them are avoidable at the planning stage, at no cost, if you know what to look out for. Here is the list that actually causes trouble.
Working in Katy
Katy covers a lot of ground. Parts sit in Harris County, parts in Fort Bend, parts in Waller, and only some addresses are actually inside the City of Katy — which affects who permits and inspects the work. The housing runs from late-1970s and 1980s neighborhoods through the master-planned build-out of the 1990s and 2000s and on into current construction. In the 80s and 90s homes we see oak cabinets, laminate counters, a garden tub with a narrow shower beside it, formal rooms nobody uses, and enough polybutylene supply piping that it is worth confirming before you commit to a bathroom. Homes that have taken water at some point come with different priorities: tile or a quality LVP instead of wood, outlets set higher than standard, closed-cell foam in place of batt. The clay moves here, so substrate flatness and movement joints get the same attention as the tile selection. Most neighborhoods have HOA architectural review.
What we actually do
Mistake one: ordering cabinets before appliances are selected. Cabinet openings are built to specific appliance dimensions. A refrigerator chosen after the fact rarely fits the opening built for a generic one, and modifying a finished cabinet run is ugly work.
Mistake two: deciding on lighting and outlets after drywall. Under-cabinet lighting, island outlets, a pot filler, a dedicated microwave circuit, and appliance loads all have to be roughed while walls are open. Adding them later means opening finished walls.
Mistake three: assuming a wall can come out. In a house that has been remodeled before, load paths are not always where you expect. Removal needs the load carried properly, engineering where required, and a permit.
Mistake four: templating countertops from drawings. Stone is templated from installed, leveled, secured cabinets. Nothing earlier is reliable.
Mistake five: ignoring the panel. A modern kitchen wants multiple dedicated circuits. An older panel with no capacity is discovered too late in a lot of projects.
Mistake six: no contingency in an older home. Cast iron, galvanized, aluminum branch wiring, and pre-1980s materials are common enough here that a budget with no room for them is a budget that will be renegotiated.
Mistake seven: skipping dust containment, which turns one dirty room into a whole dirty house.
Choosing materials
If boxes are staying, the upgrade money goes into hardware and work surfaces: full-extension undermount soft-close slides, new plywood or dovetailed drawer boxes sized to the existing opening, concealed hinges with six-way adjustment, and a countertop and sink chosen for hard water. If boxes are going, plywood construction is worth specifying over particleboard for the whole run and non-negotiable at the sink base. Doors are a separate decision: painted MDF is stable and holds a crisp profile but chips at the edge, while solid rail-and-stile hardwood moves seasonally in this humidity and shows a witness line at the panel. Splash and floor decisions interact with slab movement, so tile gets a decoupling membrane and perimeter movement joints rather than being bonded rigidly wall to wall. Where the layout changes, the drain material transition from cast iron to PVC gets a proper shielded coupling. None of this is exotic; it is just specified for a humid house on a moving slab.
Why this is different on the Gulf Coast
Two Houston-specific sequencing mistakes deserve their own mention.
The first is deciding to move the sink casually. In a slab-on-grade house the kitchen drain runs in or under the slab, and relocating it means either breaking and patching concrete, tunneling, or rerouting overhead. On a post-tension slab in a newer Katy, Cypress, or Fulshear home, cutting without locating the cables first is not an option at all. This one decision can change a project’s budget more than an entire cabinet upgrade, and it should be made early with the cost on the table.
The second is range hood ventilation. Houston kitchens increasingly get high-output hoods, and pulling that much air out of a house in this climate without a plan for makeup air can cause backdrafting at combustion appliances and can drag hot, humid outside air in through every gap in the building. It is a mechanical design question that belongs at rough-in, not a decision to be made when the hood shows up.
In older homes, popcorn ceilings and floor mastics predating the early 80s should be tested before demolition, not scraped and swept.
Where these jobs fail
The expensive one is cutting into a post-tension slab without scanning. A severed tendon is a structural repair, not a plumbing repair, and it happens most often on island drain relocations. Second is capping or transitioning cast iron badly, so a joint that is fine on day one weeps under a new floor for a year before anyone notices the grout darkening. Third is removing a wall on the assumption it is non-bearing because the ceiling looks flat; in 1960s and 70s ranches the run of ceiling joists is often perpendicular to what people expect, and the header has to be sized before the wall is opened, not after. Fourth is setting cabinets on an unlevelled slab and chasing the error into the countertop, so the dishwasher will not sit square and the drawer fronts show a wedge of shadow. Fifth is venting a range hood into the attic or into a dead soffit, which in this humidity puts grease-laden moist air into a space that never dries. Sixth is reusing old two-wire, ungrounded receptacle circuits behind new counters.
What to expect
The way we run it is designed to force the decisions early. Selections — cabinets, appliances with model numbers, countertop material, plumbing fixtures, lighting — get made before demolition, because every one of them affects rough-in dimensions or lead time.
Then protection and demolition. Then a documented walk at open walls where anything discovered is shown to you with options and costs before it gets covered. Rough plumbing, gas, and electrical, including every circuit and lighting run identified in planning. Inspections where the work is permitted, which differs across the City of Houston, unincorporated Harris County, and Fort Bend County.
Drywall, paint, flooring, then cabinets set from the floor’s high point, shimmed, ganged, and scribed. Countertop template only after that. Fabrication window. Install, backsplash, plumbing and electrical trim, appliances, punch.
We would rather spend an extra week on decisions before demolition than a month recovering from one made late.
What moves the price
Almost everything on the list above costs nothing to get right and a great deal to fix. Selecting appliances before ordering cabinets is free. Deciding on lighting and outlets before drywall is free. Confirming whether a wall is bearing before demolition is cheap.
The genuine cost drivers underneath are the same as always: whether the layout moves, cabinet grade and construction, countertop material and slab count, appliance package, electrical scope including panel work, and any structural change.
What the mistakes add is rework — opening finished drywall, modifying installed cabinets, refabricating a countertop, or renegotiating a budget mid-project because an older house needed plumbing or electrical work nobody planned for. In older Houston homes specifically, carrying a real contingency is not pessimism; it is how a fixed budget survives contact with a fifty-year-old slab-on-grade house.
Because the variables compound, rebuild costs typically fall in a very wide range, and the projects that stay near their estimate are the ones where selections were locked before demolition.
Common questions
Can we live in the house during the remodel?
Most people do. It works better with real dust containment, sealed HVAC returns, and a temporary kitchen set up somewhere else in the house before demolition day. Expect noise, expect the refrigerator to live in an inconvenient place, and expect the loudest days to be demolition and any concrete or tile work. We will tell you which days those are so you can plan around them.
Why do you want appliance model numbers before ordering cabinets?
Because cabinet openings, filler requirements, hood dimensions, and even countertop cutouts are built to specific appliances. A counter-depth refrigerator, a panel-ready dishwasher, and a slide-in range each impose different dimensions. Choosing the appliance after the cabinets are built is the most common source of ugly on-site modifications in a kitchen, and it is entirely avoidable with a spec sheet at planning.
We want to move the sink to the island. Is that a big deal?
In a slab-on-grade house, yes. The drain runs in or under the slab, so relocating it means concrete work, tunneling, or an overhead reroute, and on a post-tension slab the cable layout has to be located first. It is often the single largest cost decision in a kitchen. It is entirely doable — it just needs to be priced honestly at design rather than assumed.
How much contingency should we hold back?
Enough to absorb what an older house can reveal — piping in poor condition, panel capacity, aluminum branch wiring, or a floor that needs leveling. The exact figure depends on the age and condition of your house, and we would rather have that conversation with you honestly at the start than present it as a surprise later. Newer homes generally need less of it.
Do you cover Katy 77450?
Yes. Katy 77450 is about 5.7 miles from our shop at 1530 W Sam Houston Pkwy N, Houston, TX 77043, inside the area we work in daily. Call (281) 235-6971 to arrange a site visit.
MS Home Remodeling — kitchen demo and rebuild in Katy, TX 77450. Call (281) 235-6971 for a site visit.