Home › Services › Kitchen Cabinet Refacing › Thompsons 77481

Kitchen cabinet refacing for homes in Thompsons, TX 77481 — about 20 miles from our shop at 1530 W Sam Houston Pkwy N, Houston, TX 77043.

Refacing looks simple in a before-and-after photo and is unforgiving in practice, because every part of it is visible. There is no drywall to hide behind and no paint to bury a gap. The face frame veneer has to lie flat with tight seams. The doors have to hang with even reveals across a whole run. The end panels have to meet the countertop cleanly. Getting there depends on measuring correctly weeks earlier and on prep work that nobody photographs. This is the sequence a refacing job actually follows in a Houston kitchen, and where the care has to go.

Thompsons homes and this work

Thompsons is a very small Fort Bend County town near the Brazos south of Sugar Land, and there is no typical house here to describe honestly. It is rural — acreage, a limited number of homes, a wide spread of construction dates and building types, and a reasonable likelihood of private well and septic rather than city utilities. What that means in practice is that we approach projects here property by property rather than by neighborhood pattern. Water hardness, septic capacity if you are adding a bathroom rather than replacing one, service size at the panel, and how the structure is actually framed are all things we confirm on site instead of assuming. Elevation and floodplain status vary along the river corridor and should be checked for the specific parcel. The Gulf Coast constants still apply: expansive clay moves seasonally, humidity stays high year-round, and the details that manage both are what keep a remodel looking right in year five.

How the job is built

Measuring is the first and most consequential step. Every opening is measured individually, because cabinet openings in a kitchen built forty years ago are not identical even when they were meant to be. Overlay, hinge type, and door style are confirmed together, since they interact. Drawer front sizes are taken separately from door sizes. Everything is documented per cabinet position.

When material arrives, work starts with removing all doors, drawer fronts, hinges, and hardware. Face frames are cleaned of decades of cooking residue, which matters because adhesive will not bond through it, then sanded to give the veneer or skin something to key into.

Exposed cabinet ends are skinned first, scribed to the wall and cut to meet the countertop and toe kick cleanly. Then face frames are covered, with seams placed where the eye does not land and edges rolled tight.

Doors go on next with new concealed hinges. Every door gets adjusted for reveal, and on a long run that adjustment is iterative rather than one pass. Drawer boxes or glides get replaced where worn. Then hardware, crown or light rail, new toe kick, and fillers. Final pass is cleaning and a door-by-door check.

Products and materials

The material choices you make change how the job feels to live with. Pressure-sensitive veneer and laminate systems produce less odour than solvent contact adhesive, which is a real consideration in a sealed house. Pre-finished doors arriving complete from the supplier mean no spraying and no finish cure time in your kitchen, which is the main logistical advantage refacing holds over painting the existing doors in place. Where doors are painted on site instead, add containment and cure time to your expectations. Soft-close hinges and undermount slides arrive as hardware, not as a wet trade, so those stages are quiet. Toe kick material, usually a matching laminate or vinyl, goes on late and quickly. If under-cabinet lighting is being added, that is electrical work with its own permitting path in Houston and its own separate visit, and it should be sequenced before the frames are skinned rather than after.

Local building realities

Two Houston conditions affect this work directly. The first is grease and humidity on the existing face frames. Kitchens here run warm and humid, and cooking residue combines with airborne moisture into a film that resists adhesion. Skipping the degreasing step produces veneer that bonds beautifully for a season and lifts at an edge afterward. It gets cleaned properly and mechanically abraded before anything is applied.

The second is that cabinet runs in Houston homes are frequently no longer plumb. Slab-on-grade over expansive clay moves seasonally, and a run of cabinets installed decades ago has ridden that movement. Old doors hid it because they were adjusted, or simply hung crooked and nobody noticed. New doors with crisp reveals expose everything. Where a run has shifted, boxes get shimmed and re-secured before new fronts go on, otherwise the reveal will taper visibly from one end to the other.

Third, we schedule with humidity in mind. Adhesives and finishes behave better in a conditioned space, so the kitchen stays closed up and running on air conditioning during the work rather than opened to an August afternoon.

What to watch for

The common tier mistake is spending on doors and reusing worn drawer mechanics, so a kitchen that looks new still sticks and rattles every day. The second is choosing thermofoil throughout and putting it next to a dishwasher and a range without accepting where it will fail first. Third, buying wood veneer frames without paying for the surface preparation veneer demands, since old finish, cooking residue or sanding dust will defeat the adhesive regardless of veneer quality. Fourth, skipping frame correction at any tier and then blaming door quality for uneven reveals. Fifth, leaving interiors untouched behind high-specification doors, so every opening reveals the old kitchen. Sixth, mixing tiers within one visible run, where a budget end panel sits beside mid-tier doors. Seventh, spending up on the kitchen while a leaking supply line under the sink continues quietly wetting the box that everything is fastened to.

How a project runs

First visit is measurement and assessment together. We open everything, check box condition, verify the runs, and take opening-by-opening measurements. You choose door style, material, finish, and hardware.

Then there is a wait. Doors are made to your sizes, and that lead time is a fixed part of the schedule that no amount of scheduling pressure changes.

On install, we remove doors and hardware, degrease and prep, correct box issues, skin ends, apply face frame material, hang doors, replace glides and drawer boxes as scoped, install hardware and trim, then adjust every door and drawer.

We try to leave the kitchen functional through the process, since the boxes and countertops never leave. Expect a few dusty days rather than weeks without a kitchen.

We walk the finished kitchen with you and adjust anything that is not sitting right.

Cost factors

Door count and style are the base. Painted shaker in MDF sits lower than solid hardwood with a stained finish, and stain grade requires more selective material.

Cabinet complexity adds: glass doors, angled corners, tall pantry units, appliance panels, and any open shelving each carry extra fabrication or fitting.

Condition of the existing boxes is the variable that moves quotes most. Repairing a water-damaged sink base, replacing toe kicks, re-shimming a run that has gone out of plumb, or reinforcing a face frame all happen before the visible work starts.

Drawer upgrades are a common add. Replacing tired glides with soft-close undermount hardware, or replacing whole drawer boxes, is usually worth doing while everything is apart and is a real line item.

Finally, what else joins the project. New countertops, a backsplash, under-cabinet lighting, and hardware all commonly ride along with refacing, and they can easily exceed the refacing cost itself.

Common questions

How long does refacing take once the doors arrive?

The on-site portion is considerably shorter than a full remodel because there is no demo, no countertop work, and no plumbing. The actual duration depends on cabinet count and whether box repairs are needed. The longer part of the timeline is fabrication of the doors after measuring. We give you a schedule for your specific kitchen rather than a generic number.

Will the new doors match my existing crown molding?

They will not, and that is why crown and light rail are normally replaced as part of the job. Old trim in a different species or finish sitting above brand new doors is the most common way a reface looks unfinished. Replacing the trim, toe kick, and filler pieces so nothing original remains visible is what makes the result read as new cabinetry.

Can I keep my countertops?

Yes, and that is one of the real advantages. Refacing does not require removing the tops, which avoids both the cost of new counters and the risk of damaging existing stone during removal. The exposed end panels get scribed to meet the countertop cleanly. If you want new counters anyway, doing both together is efficient sequencing.

Do the drawer boxes get replaced too?

Only if you want them to, but it is often the best value in the project. New drawer fronts on forty-year-old wooden glides means you still fight the drawer every day. Converting to soft-close undermount glides, or replacing the boxes entirely, is the upgrade most homeowners say they notice most after the job is finished.

Do you cover Thompsons 77481?

Yes. Thompsons 77481 is about 20 miles from our shop at 1530 W Sam Houston Pkwy N, Houston, TX 77043, inside the area we work in daily. Call (281) 235-6971 to arrange a site visit.

MS Home Remodeling — kitchen cabinet refacing in Thompsons, TX 77481. Call (281) 235-6971 for a site visit.

MS Home Remodeling · 1530 W Sam Houston Pkwy N, Houston, TX 77043 · (281) 235-6971 · All kitchen cabinet refacing locations