Home › Services › Under Cabinet Lighting › Katy 77450

Katy 77450 sits about 5.7 miles from our shop, and under cabinet lighting is work we do there regularly.

Under-cabinet lighting is a job where the fixture is the easy part. What sets the scope is the wall behind the backsplash and the year the house was framed. A 1970s kitchen in Oak Forest and a 2006 kitchen in Cinco Ranch end up with the same band of light on the counter, but almost nothing between the panel and the cabinet is the same. The older house often has a switch loop with no neutral, shallow boxes, a crowded panel, sometimes aluminium branch wiring. The newer one frequently has a builder whip already sitting above the wall cabinets, left from puck lights nobody liked. Same finished look, two different jobs.

Why this is different on the Gulf Coast

Two Houston conditions drive the details. Heat: drivers pushed into a soffit or attic space sit in air that gets brutally hot for months, and electrolytic capacitors are what die there, so drivers go in conditioned cabinet space wherever the run allows. Humidity plus cooking grease: adhesive-backed tape mounted straight to a cabinet bottom lets go, usually at the ends first, so tape rides in a mechanically fastened channel. Inner-loop stock from the 1960s to early 80s brings its own list, including aluminium branch circuits from the late-60s window and ungrounded runs. Homes that took water in a flood event often had lower walls re-rocked and rewired, which is the moment to add a proper lighting circuit while the wall is open. Permitting differs by jurisdiction, and adding circuits inside the City is treated differently than in unincorporated Harris or Fort Bend, so that gets confirmed before anything is cut.

What we actually do

Work starts at the panel and in the attic, not at the cabinet. We find a lighting circuit that can carry the load, confirm whether the switch box has a neutral, and check whether there is room for a dimmer at all. In older stock we pull the device, look for aluminium conductors, check box depth and fill, and often swap in a deeper old-work box. Then layout: fixtures go at the front edge of the cabinet bottom, behind the light rail where one exists, so the source stays out of a seated sight line. The driver is placed somewhere reachable, inside an upper cabinet or above a soffit, never sealed behind finished drywall. Then the route. Low-voltage is fished down cabinet gables through grommeted holes or across the backs of the uppers; line voltage feeds the driver from the switch. Aluminium legs get connectors listed for aluminium-to-copper. Extrusion is screwed to the cabinet bottom, tape seated in the channel, diffuser snapped in, runs cut only at marked cut points. Last is dimmer commissioning and a check for flicker at the low end.

Choosing materials

Three fixture classes cover nearly everything. LED tape in an aluminium extrusion with a frosted diffuser gives the most even wash and the channel doubles as a heat sink. Linear bars are pre-built versions of the same idea, easier in a retrofit with limited access. Pucks throw scallops and hot spots on polished quartz and are mostly a legacy choice. Colour matters more than people expect: 2700K to 3000K sits with warm white cabinets and most Houston kitchen palettes, and CRI in the 90s with decent deep-red rendering keeps meat and produce from looking grey on the counter. Constant-voltage 24V is preferred over 12V because voltage drop over a long galley run shows up as dimmer light at the far end. The driver and the dimmer have to be a tested pair. Forward-phase dimming on a cheap driver is where flicker, buzzing and a dead low end come from. Near the dishwasher and sink, choose a run rated for damp exposure rather than bare tape.

What moves the price

Access is the biggest lever. A wall already open during a remodel is a fraction of the labour of fishing behind a finished tile backsplash. Whether a usable lighting circuit and a neutral already exist decides whether a new home run and panel work enter the job. Total run length and the number of separate cabinet segments drives both material and connection count. Dimming choice matters: a basic tested driver-and-dimmer pair costs far less than tunable white with a compatible control. Cabinet construction plays in too, since frameless boxes with no light rail need a recessed channel to hide the source. Aluminium branch wiring remediation, a crowded panel, and permit and inspection requirements in some jurisdictions all add scope.

What we see in Katy

Katy covers a lot of ground. Parts sit in Harris County, parts in Fort Bend, parts in Waller, and only some addresses are actually inside the City of Katy — which affects who permits and inspects the work. The housing runs from late-1970s and 1980s neighborhoods through the master-planned build-out of the 1990s and 2000s and on into current construction. In the 80s and 90s homes we see oak cabinets, laminate counters, a garden tub with a narrow shower beside it, formal rooms nobody uses, and enough polybutylene supply piping that it is worth confirming before you commit to a bathroom. Homes that have taken water at some point come with different priorities: tile or a quality LVP instead of wood, outlets set higher than standard, closed-cell foam in place of batt. The clay moves here, so substrate flatness and movement joints get the same attention as the tile selection. Most neighborhoods have HOA architectural review.

Where these jobs fail

Tapping the countertop small-appliance circuit for lighting is the common shortcut and it is the wrong source; lighting belongs on a lighting circuit. Burying the driver behind new drywall guarantees that the first failure becomes a repair with a drywall patch. Mounting the strip at the back of the cabinet instead of the front edge bounces the source off a polished granite or quartz top straight into your eyes. Skipping the diffuser leaves visible dots and a striped reflection on gloss backsplash tile. Mixing colour temperatures so under-cabinet light reads cool against warm recessed cans makes the whole kitchen look mismatched. On older wiring, pigtailing copper to aluminium with standard twist-on connectors is a real hazard, not a cosmetic issue. Running low-voltage and line-voltage conductors through the same unbushed hole invites both chafing and noise. And raking light across the counter shows everything, so hard-water film on the backsplash and an uneven grout line become visible the moment the light goes on.

What to expect

A first visit covers the panel, the switch box, the attic or soffit above the cabinets, and the counter surface you are lighting. From there we set fixture positions, driver location and the wire route on paper before anything is opened. Electrical work is done and inspected where the jurisdiction requires it. Channels are mounted, tape seated and terminated, then the dimmer is set and the low end checked for flicker with the room dark. We clean the counter and backsplash before the final look, because the new light will show whatever is left behind. To have your kitchen looked at, call (281) 235-6971.

Common questions

Do I need a permit for this in Houston?

Electrical work is permitted here, and requirements differ between the City and unincorporated Harris or Fort Bend County. Simply replacing an existing plug-in fixture is different from adding a circuit. We confirm the requirement for your address before scheduling rather than guessing.

My 1970s kitchen has no neutral at the switch. Is that a dealbreaker?

No, but it changes the work. Options include pulling a new switch leg with a neutral, feeding the driver from a different lighting circuit, or relocating control. What we avoid is a workaround that leaves the driver unreachable or the switch box overfilled. It gets decided after the box is opened.

There is already a junction box above my wall cabinets. Can we just reuse it?

Often yes. Builder whips left for puck lights are common in 2000s suburban kitchens and can feed a modern driver, provided the circuit and switch check out. We verify the source, the conductor size and the switch device before assuming it is usable.

Do you cover Katy 77450?

Yes. Katy 77450 is about 5.7 miles from our shop at 1530 W Sam Houston Pkwy N, Houston, TX 77043, inside the area we work in daily. Call (281) 235-6971 to arrange a site visit.

MS Home Remodeling — under cabinet lighting in Katy, TX 77450. Call (281) 235-6971 for a site visit.

MS Home Remodeling · 1530 W Sam Houston Pkwy N, Houston, TX 77043 · (281) 235-6971 · All under cabinet lighting locations