Home › Services › Open Concept Kitchen Remodel › Houston 77019

Looking at open concept kitchen remodel in Houston 77019? That’s around 14 miles from us, well inside the area we work daily.

Two kitchens on opposite sides of the metro, same request: take out that wall. It is not the same job. A 1968 ranch off Bingle has stick-framed ceiling joists that almost certainly bear on the wall you want gone, a cast iron stack hiding somewhere in it, and possibly aluminium branch wiring feeding the counter receptacles. A 2004 house in Bridgeland has clear-span roof trusses, PEX supply, and a post-tension slab nobody should cut before it is scanned. Both open up. They open differently, the surprises arrive from different directions, and the age of the house sets much of the budget before anyone picks a countertop. This page walks the contrast, so you know which conversation you are about to have.

Local building realities

Post-tension slabs are the sharp edge on the west side. Much of the post-1985 stock in Katy, Cypress and Fulshear sits on cable-tensioned concrete, and the pad under a new post has to be located by scanning before a saw touches anything. Cutting a tendon is not a patch; it is a specialist repair and a bad week. Inner-loop houses sit at the other extreme: 1950s and 60s slabs poured on Beaumont clay that has been shrinking and swelling ever since, or pier-and-beam floors where the wall you want gone is carried on a beam and blocks below, so the load path continues under the floor rather than into a footing.

Expansive clay also changes what happens afterwards. Two rooms with a wall between them hid differential movement at the wall line. One continuous floor does not. That is why open-plan flooring gets an uncoupling or crack-isolation membrane and real perimeter movement joints instead of grout run tight to the baseboard.

How the job is built

The framing gets read, not guessed. In older stick-framed stock that means going into the attic and following the ceiling joists to see what they land on, looking for a ridge board versus a ridge beam, and noting purlin braces that dump roof load onto the wall from above. In truss-framed suburban houses it means confirming whether the truss overhead genuinely clear-spans, and whether a girder truss or a hip set lands a point load near the opening.

Then the load path is drawn all the way down: beam, posts at each end, and something under those posts able to carry them. On slab-on-grade that usually means a thickened pad or a poured pier, which means cutting concrete. Temporary shoring goes up on both sides before a stud comes out.

After that, in order: demolition, beam set, posts and connectors, then rerouting whatever lived inside the wall — vent stack, supply lines, branch circuits, a duct. Ceiling framing is spliced and levelled across the old wall line, drywall patched and textured to match, HVAC supply and return rebalanced for one larger room, the slab ground and floated where two floors used to meet, then cabinets, counters, hood duct and finishes.

Products and materials

Beam choice is depth against budget. Engineered lumber — LVL for ordinary spans, PSL where a girder or hip load lands on an end post — is the common answer and the cheapest to set. Steel enters when the beam must sit flush inside the ceiling plane and the span will not tolerate the depth an LVL needs. A flitch plate sandwiched in wood is the middle ground. The connectors and posts are part of that design, not an afterthought.

For cabinets in this climate, plywood boxes over particleboard is the specification that matters. Particleboard swells permanently the first time a sink-base supply weeps, and our humidity keeps everything at a higher moisture content year round. Thermofoil doors beside a range delaminate. Painted MDF door panels stay flatter through the humidity swing than solid wood.

Counters: quartz is the low-maintenance default, but a slab in direct west sun through a newly opened wall of glass can shift colour over years, which is where granite, quartzite or porcelain earn their place. Marble etches, and hard-water scale gets scrubbed off, which accelerates it. Textured ceilings in pre-1980 houses get tested before removal rather than scraped on a hunch.

Cost factors

Whether the wall carries load is the first fork, and it is worth paying to answer early. After that, roughly in order of impact: the span, and whether the beam is dropped or flush, since flush usually means steel and heavier connections; the foundation work under the new posts, which on a post-tension slab includes scanning; and whether plumbing moves. A sink or dishwasher relocated to a new island means trenching the slab for drain and vent, and that is a different job from leaving the sink where it is.

Then the older-house items: aluminium branch wiring needing pigtailed terminations, an undersized panel, cast iron drain in poor condition, testing on textured ceilings. Then the visible choices — cabinet construction and finish, slab count and seams in the counters, the appliance package, and how much ceiling and floor must be rebuilt so the space reads as one room instead of two.

Working in Houston

Houston is not one housing stock, so it is not one kind of remodel. In the Heights and Woodland Heights you are often working on 1910s–1930s wood-frame homes on pier-and-beam, where leveling, sill and joist repair, and original wiring long past its service life come before anything cosmetic — and where a home in a designated historic district brings design review with it. Montrose, Oak Forest and Garden Oaks add mid-century layers. Meyerland, Westbury, Braeswood and Sharpstown are largely 1950s–60s slab ranch: cast iron drains near the end of their life, galvanized supply, single-pane windows, popcorn ceilings that should be tested before they are disturbed. Memorial and Alief lean 1970s–80s, which brings aluminum branch wiring and polybutylene supply into the conversation. West of Beltway 8 you are usually in 2000s and 2010s construction, where the job is upgrade rather than repair. Houston has no zoning, but plumbing, electrical and structural work is permitted, and deed restrictions still govern a great deal.

What to watch for

The costly one is calling a wall non-bearing because the house has trusses. Trusses clear-span until a girder truss or a hip set does not, and suburban hip roofs put point loads in places that look like open ceiling from below. Read the attic first.

Second, the load path that stops at the slab. A beam is only as good as the post beneath it, and the post is only as good as what sits under the concrete at that spot. Ordinary residential slab thickness is not a footing. If the drawing does not show what happens below the post, it is unfinished.

Third, sawing a post-tension slab without scanning. Fourth, opening the wall before locating the kitchen vent stack, then improvising a route through a ceiling already framed. Fifth, flooring: large-format porcelain across a formerly two-room span shows every high spot as lippage, and the slab under the old wall line is rarely flat, so it gets ground and floated before tile rather than after complaints. Sixth, air. One combined room needs return air, and a range on an island needs a genuinely ducted hood with a short run. A recirculating unit in a humid open plan just relocates the grease and steam.

How a project runs

It starts with an attic and a tape measure. We look at framing, the panel, attic ducting and where the drain lines run before discussing layout, because those four things decide what is possible. Where the wall is structural, a Texas-licensed structural engineer specifies the beam and the bearing, and that sealed drawing is what the permit and the inspection are built on. The City of Houston has no zoning but does permit structural, plumbing and electrical work, and unincorporated Harris or Fort Bend runs its own process, so we confirm which applies to your address instead of assuming.

From there: selections locked before demolition, shoring, demolition, beam, rough-in and inspection, close-up, floor prep, cabinets, template, counters, punch list. To have that read done on your house, call (281) 235-6971.

Common questions

How can I tell whether my kitchen wall is load-bearing?

From below you cannot, reliably. It is decided in the attic: which way the ceiling joists run, what they bear on, whether a splice sits over that wall, and whether purlin braces or a girder truss land load there. A wall running perpendicular to the joists with a bearing splice above it is carrying weight until an engineer says otherwise.

Can a post-tension slab be cut for a new footing?

Yes, but only after the tendons are located. Scanning maps the cable layout so the opening falls between them, and the pour and any needed repair detail follow the engineer's direction. Cutting first and discovering a tendon afterwards turns a small pad into a structural repair. On post-1985 west-side houses, assume post-tension until you have proof otherwise.

Does the new beam have to show in the ceiling?

No, though hiding it costs more. A dropped beam sits below the ceiling and is the cheaper, faster option; it can be wrapped and trimmed so it reads as deliberate. A flush beam is framed up inside the ceiling plane, usually needs steel or a deeper engineered member with the joists hung off it, and takes more framing labour.

Is an older Houston house always more expensive to open up?

Not always, but it carries more unknowns: cast iron drains, galvanised supply, aluminium branch wiring, plaster, textured ceilings needing testing, and framing that actually bears on the wall. Newer suburban houses trade those for post-tension slabs and hip-roof point loads. Older homes tend to have more items discovered after demolition, so the contingency conversation matters more.

Do you cover Houston 77019?

Yes. Houston 77019 is about 14 miles from our shop at 1530 W Sam Houston Pkwy N, Houston, TX 77043, inside the area we work in daily. Call (281) 235-6971 to arrange a site visit.

MS Home Remodeling — open concept kitchen remodel in Houston, TX 77019. Call (281) 235-6971 for a site visit.

MS Home Remodeling · 1530 W Sam Houston Pkwy N, Houston, TX 77043 · (281) 235-6971 · All open concept kitchen remodel locations