Home › Services › Bathroom Vanity Installation

Houston Metro · Residential & Commercial

Bathroom Vanity Installation in the Houston Metro

A vanity swap in a 1968 ranch off Wirt Road and a vanity swap in a 2006 house in Cinco Ranch read the same on an estimate and are not the same job. The older bathroom usually hands you multi-turn compression stops that weep the…

Licensed & Insured
20+ years remodeling
17 cities served
102 ZIP codes covered

Call (281) 235-6971 Request an estimate

In short

What the work involves

Water off at the stops, and off at the main when the stops are the original multi-turn type, because those often will not reseat once turned. The trap and supplies come off, the silicone bead at the wall and floor is cut with a blade rather than pulled, and the old cabinet comes out in one piece where the room allows. Then the wall gets read. In older stock that usually means patching torn drywall or skim-coated plaster, taking off a four-inch tile splash bedded over paper facing, and dealing with whatever the old cabinet was hiding. Stops get replaced with quarter-turn ball stops; where a galvanised branch is scaled down internally, the plumber makes a transition rather than threading onto rotten pipe. Newer bathrooms often skip that and go straight to setting. The cabinet is levelled from the highest point of the floor, shimmed at the base, and anchored into studs or blocking, never into drywall alone. Filler strips are scribed to the wall. The top is templated after the box is set and confirmed level, fabricated off site, then set with the bowl already attached. Faucet, drain, trap, splash, caulk joints, and the electrical at the mirror close it out.

What gets specified, and why

Plywood boxes over particleboard, and it matters more here than in a dry climate. Particleboard and thin MDF do not simply get damp and dry out; they swell at the core and stay swollen, so one slow supply drip in a Houston bathroom ends the cabinet. Dovetailed solid drawer boxes on undermount slides survive humidity swings better than stapled boxes with epoxy side slides. On finishes, a factory-applied catalysed coating holds up better at drawer edges and the toe kick than site-brushed paint; thermofoil wrapped doors delaminate at the top edge above a hair dryer or a steam-heavy shower. For tops, engineered quartz is the low-maintenance default because it does not need sealing and shrugs off hard-water scale that etches marble. Granite is fine but wants periodic sealing. Cultured marble with an integral bowl is honest budget material and it does scratch and dull. Under the cabinet, quarter-turn ball stops, braided stainless supply hoses with the nut and gasket properly seated, and a solid trap. In an older house with aluminium branch wiring, the receptacle at the vanity needs CO/ALR-rated devices or an approved pigtail, not a standard one.

Why the Gulf Coast changes this job

Inner-loop bathrooms from the 1950s through the 1970s frequently still drain through cast iron. It works until it is disturbed, and a corroded hub or a soft closet bend behind the vanity wall becomes a plumbing job rather than a cabinet job. Better to find that while the wall is open than after the stone is set. Houses in Katy, Cypress and Fulshear built from the mid-1980s on often sit on post-tension slabs, which means nothing gets drilled into the slab for a console leg or floor anchor without knowing where the tendons run. Both ends of the metro share two problems. Expansive clay moves the slab seasonally, so a bathroom floor is rarely flat and a top scribed dead tight in February can show a hairline at the wall by August, which is why every change of plane gets a flexible joint instead of grout. And the humidity never really leaves. A bathroom with a weak or unducted exhaust fan takes a cabinet apart from the toe kick upward no matter what the cabinet cost.

Where these jobs go wrong

Anchoring the cabinet through drywall into nothing. It feels tight the day of and works loose as the box takes weight and the door swings. Not replacing old stops because they were not leaking beforehand, then discovering they will not close when a hose fails at two in the morning. Setting a stone top on a box that is level side to side but racked front to back, which puts a stress line straight through the thin section at the sink cutout. Ordering a drawer-bank vanity without first measuring where the trap arm exits the wall, so the drawer backs have to be hacked out on site or the drain relocated after the fact. Reusing existing flexible supply lines because they look fine. Grouting the cabinet to the tile instead of caulking, which gives seasonal slab movement a rigid joint to crack. Mounting the faucet and drain assembly after the top is set, when the only access left is on your back inside the cabinet. And running a new vanity into a bathroom whose exhaust fan is either disconnected in the attic or was never big enough for the room.

What moves the price

The cabinet is usually not the biggest number. What moves the price is whether the plumbing has to move: a drain relocation, a supply reroute, or a transition off galvanised is real trade time behind an open wall. Countertop material and edge profile, single bowl versus double, and whether the bowl is undermount in stone or integral in a cast top. Wall-hung vanities need blocking, which means opening and repairing drywall. Tile repair at the old footprint, where the floor or splash tile stops short of the new cabinet outline, is a frequent surprise in older houses. Add electrical if the vanity light, mirror, or receptacle are being changed, or if there is no GFCI protection at the counter. Access matters too, upstairs versus down, tight hallway, narrow doorway. Ranges quoted over the phone are guesses; the honest version comes after someone looks under the existing cabinet.

How a project runs

We walk the bathroom, look under the existing cabinet, check the stops and the branch piping, and measure the rough-in heights before anything is ordered. Selections get confirmed against those measurements rather than the other way around. Demolition and set happen together so the room is not open longer than it needs to be. The top is templated only after the box is set and verified level, then fabricated off site, so there is a gap between set day and top day, and we plan the water shut-offs around it. Final visit is faucet, trap, splash, caulk, and cleanup. If you want an actual look at yours, call (281) 235-6971.

Common questions

My house is from the 1970s. Will a new vanity fit the same footprint?

Often not exactly. Older cabinets were built in different widths and depths, and the floor tile frequently stops at the old cabinet outline instead of running underneath. A narrower or shallower replacement exposes bare subfloor or an untiled strip. We measure the existing footprint and the tile edge first, then either match the outline or plan the floor repair into the job.

Do the shut-off valves really need replacing?

On older multi-turn compression stops, usually yes. They sit untouched for decades, the packing hardens, and the first turn is often the last one they take. Replacing them with quarter-turn ball stops during a job the water is already off for is cheap insurance and it means the next repair does not start with a trip to the main.

Can I keep my existing countertop and just change the cabinet?

Rarely worth attempting. Stone tops are bedded in silicone and typically break during removal, especially at the thin sections beside the sink cutout. Even undamaged, an old top seldom matches a new cabinet’s width or overhang. If the top is in good condition and you like it, the more sensible conversation is refinishing or replacing doors and drawer fronts instead.

Is a permit needed to change a vanity?

It depends on what the work actually touches. Houston permits plumbing and electrical work, and swapping a fixture in place is not treated the same as relocating a drain or adding a circuit. Unincorporated Harris and Fort Bend County run their own processes. We confirm what a specific address requires before starting rather than assuming, and we do not quote fees or timelines we have not verified.

Bathroom Vanity Installation by location

We cover 102 ZIP codes across the Houston metro. Pick the area closest to you:

Planning bathroom vanity installation?

We measure, look at the slab and the existing rough-in, and give you a scope you can actually compare against another bid.

Call (281) 235-6971

MS Home Remodeling · 1530 W Sam Houston Pkwy N, Houston, TX 77043 · (281) 235-6971

Kitchen remodeling

Cabinets & counters

Planning

Bathroom remodeling

Planning

Whole-home renovation

Additions

Interior

Exterior

Outdoor living

Flooring

Commercial remodeling

Build-out & occupancy

Building in Houston

Planning a project

Company

Where we work

Kitchen remodeling

Cabinets & counters

Planning

Start with a measured visit

Bathroom remodeling

Planning

Start with a measured visit

Whole-home renovation

Additions

Interior

Start with a measured visit

Exterior

Outdoor living

Flooring

Start with a measured visit

Commercial remodeling

Build-out & occupancy

Start with a measured visit

Building in Houston

Planning a project

Start with a measured visit

Company

Start with a measured visit

Where we work

Bathroom Vanity Installation in the Houston Metro

In short

What the work involves

What gets specified, and why

Why the Gulf Coast changes this job

Where these jobs go wrong

What moves the price

How a project runs

Common questions

Bathroom Vanity Installation by location

Planning bathroom vanity installation?

Related Remodeling Services